• Auto-hand
    • Lada Granta
    • Lada Kalina
    • VAZ-2121
    • Lada-Largus
    • Lada Priora
    • Lada Vesta
  • separator
    • GAZ-66
    • GAZ-2705
    • GAZ-3110 (Volga)
  • Separator-2
  • Engines
    • UAZ 3151
    • Niva Chevrolet
    • ZIL-5301
    • MAZ
    • Ural car
    • ZIL-131
    • Auto PAZ
    • Kamaz
  • Separator-3
  • Systems
  • separator-4
  • search

Select your language

  • Русский
  • Қазақша (kk-KZ)
  • Українська (Україна)
  • Español (España)
  • German (DE)
  • English (UK)

Checking the steering of the Lada Largus

When operating a vehicle, it is necessary to regularly check the condition of the steering, as the safety of movement depends on it

Removing the heating and air conditioning control unit of the Lada Largus

Remove the control unit to replace the backlight lamp or to replace the unit itself

How to disassemble the JH3 gearbox

Install the gearbox on a special stand or workbench with the rear cover facing up

How does the K4M engine phase regulator work?

To improve the filling of the cylinders with fuel mixture in all modes, 1.6 l engines. equipped with a phase regulator of the intake valve camshaft

How to remove the air conditioner condenser Lada Largus

The condenser (air conditioner radiator) is a multi-flow type and is installed in front of the engine cooling system radiator

The condenser is attached to the cooling system radiator tanks with four brackets

How to remove oxygen concentration sensors of a Lada Largus car

Remove the oxygen sensors if they fail and when dismantling the exhaust pipes

How to remove and install rear suspension springs Lada Largus

Remove the springs if they break, sag, replace the spring gaskets, remove the beam and remove the exhaust system (you have to remove the left spring)

How to replace hydraulic valve lifters on a K4M engine

You will need: the same tools as for replacing the valve stem seals, except for those that are needed directly for replacing them (tools are used only for preparatory operations),

How to remove and install the fuel rail of the K4M engine

We remove the fuel rail to replace the injectors and to clean the fuel rail, as well as when repairing the cylinder head

We prepare the car for the work.

How to replace the radiator of a Lada Largus

Preparing the car for work

Work is performed on an inspection pit or on a lift

How to replace the clutch of a Lada Largus with a JH3 gearbox

We remove the clutch discs when they are worn out and when replacing the rear crankshaft seal and flywheel, as well as when repairing the engine

How to remove the intake manifold of the K7M engine

Prepare the car for work. Use a 10 mm wrench to unscrew and remove the negative battery terminal.

How to repair a heater in a Lada Largus

Prepare the car for work. Disconnect the negative terminal of the battery

Removal

Remove the instrument panel.

The procedure for disassembling the cylinder block of the K4M engine

After removing the engine from the car and removing the cylinder head, you can begin disassembling, repairing and assembling the engine cylinder block

How to Replace K4M Powertrain Mounts

We remove and replace the supports if they are defective or when repairing the power unit

How to install the cylinder head of the K4M engine

We install the cylinder head after repair, inspection and defect detection

How to remove the intake manifold of the K4M engine

Preparing the car for work. Disconnecting the negative terminal from the battery

Removing the intake silencer.

Removal and installation of air conditioning pipes Lada Largus

In this article we will consider the removal and installation of tubes connecting the entire air conditioning system of the Lada Largus

How to remove the front suspension stabilizer Lada Largus

The stabilizer serves for lateral stability of the car when driving

Page 6 of 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6