• Auto-hand
    • Lada Granta
    • Lada Kalina
    • VAZ-2121
    • Lada-Largus
    • Lada Priora
    • Lada Vesta
  • separator
    • GAZ-66
    • GAZ-2705
    • GAZ-3110 (Volga)
  • Separator-2
  • Engines
    • UAZ 3151
    • Niva Chevrolet
    • ZIL-5301
    • MAZ
    • Ural car
    • ZIL-131
    • Auto PAZ
    • Kamaz
  • Separator-3
  • Systems
  • separator-4
  • search

Select your language

  • Русский
  • Қазақша (kk-KZ)
  • Українська (Україна)
  • Español (España)
  • German (DE)
  • English (UK)

Disassembly and assembly of the GAZ-2705 gearbox

Disassembling the gearbox

Clean off dirt and wash the outside of the gearbox

Rolling bearings Gazelle

Before buying a bearing, you need to look at its catalog number

The table shows the bearing numbers in accordance with the spare parts catalog and the numbers in the diagram

Removal and repair of the GAZ-2705 pressure regulator

Removal of the pressure regulator from the car and its repair are carried out if adjustment cannot achieve its correct operation

To remove the regulator you must:

Cabin door GAZ-2705

Hinges are used to open the cabin door and hold it in a vertical position, and a roller-type door stop is used to limit the opening angle and fix (hold) the door in the open position

Brake pedal GAZ-2705

The full travel of the brake pedal must be at least 150 mm

How to remove and install the lower front panel of a Gazelle car

We remove the lower front panel when removing the engine, replacing the oil cooler, replacing the engine cooling radiator

Replacing the mass flow sensor GAZ-2705

The mass air flow sensor is used to determine the amount of air entering the engine cylinders

Features of the GAZ-2705 oil system

Engine lubrication system mod. 406 and 402 combined: under pressure and spray

Oil system filter GAZ-2705

Replacing the oil filter GAZ-2705

On engines mod. 406, filter 2101-1012005 is used, installed at the bottom of the cylinder block on the right side

Recommendations for the operation of the GAZ-2705

It is prohibited to coast the car with the ignition off, as this stops the operation of the power steering (power steering), and you can also accidentally lock the steering shaft with an anti-theft device, and the car will become uncontrollable

Adjustment of CO GAZ-2705

Adjusting the carbon monoxide (CO) content in the exhaust gases of ZMZ-406

Adjustment is carried out on a warm engine (coolant temperature 80-90 °C) with a working ignition system and nominal gaps between the electrodes of the spark plugs

Adjustment of the bearings of the steering gear GAZ-2705

Adjust the bearings when axial or radial play appears in the bearings of screw 2. To ensure the presence of these clearances, you must:

Maintenance of the rear axle GAZ-2705

Maintenance of the rear axle consists of:

  • - periodically checking the oil level in the crankcase, topping it up and changing it according to the lubrication chart;

Replacing the synchronization sensor GAZ-2705

The speed and timing sensor is located at the front of the engine on the right side

Using the sensor signal, the engine control unit determines the angular position of the crankshaft and its rotation speed

Oil pump drive GAZ-2705

The engine has mod. 406 oil pump is driven from the intermediate shaft, for the engine mod. 402, the pump and ignition distributor are driven from the camshaft

Steering malfunctions GAZ-2705

In this article we will look at possible faults in the steering control of a Gazelle car and how to troubleshoot problems

Adjustment of the brake pressure regulator GAZ-2705

After the first 2500 km and during maintenance-2, and also if the rear wheels of a loaded vehicle lock up earlier than the front wheels or much later when braking on a dry hard surface, you should make sure that the regulator is adjusted correctly

GAZelle suspension maintenance

In accordance with routine work on the suspension during its maintenance, it is necessary to periodically tighten the nuts of the stepladders, the nuts of the bolts of the rubber-metal hinges, the fastening parts of the spring brackets and shock absorbers

Oil cooler GAZ-2705

Removal and installation of oil cooler GAZ-2705

An oil cooler is included in the system to cool the oil

Crank mechanism UMZ-4215

Pistons - nominal diameter 100 mm, with a conical recess on the bottom, with a thermostatic insert, cast from an aluminum alloy and coated with tin

Page 5 of 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10