How to remove and disassemble the front doors of Lada Largus

: Also available:

Prepare the car for work. Disconnect the negative battery terminal

Lower the window to the lower position.

Disassembling the front door: 1 - front door trim; 2 - screw for fastening the inner front door handle; 3 - inner front door handle; 4 - speaker fastening screws

Use a Torx T30 screwdriver to unscrew screw 2, Figure 1, fastening the inner door handle 3; disconnect the lock rod from the handle, remove the handle.

Remove the trim and use a Torx T30 screwdriver to unscrew the four screws 4 securing the speaker of the acoustic system, disconnect the wiring harness block and remove the speaker.

Fastening the trim from the end: 1 - horizontal glass seal; 2 - self-tapping screw for fastening the trim on the armrest; 3 - door lock button; 4 - self-tapping screw for fastening the trim from the end

Use a T20 Torx screwdriver to unscrew the self-tapping screw 4, Figure 3, fastening the trim from the end.

Use a T20 Torx screwdriver to unscrew the self-tapping screw 2 fastening the trim on the armrest.

Removing the window lifter handle: 1 - window lifter handle cover; 2 - retaining bracket; 3 - window lift handle

For the version with a manual window lift:

- move cover 1, figure 2, of the window lift handle away from the door trim, remove the retaining clip 2, remove the handle 3.

Overcoming the resistance of the holders, detach the trim 1 (see figure 1) from the door, remove the button 3, figure 3, of the lock from the hole in the trim.

Remove the seals 1.

Temporarily connect the terminal of the “ground” wire to the battery (for the version with a manual window lift: temporarily put on the handle), lift the glass so that the window lift slider is positioned opposite the opening in the inner panel of the door.

Fastening the glass clip to the window lifter slider: 1 - front door glass; 2 - screws for fastening the glass clip to the window lifter slider; 3 - window regulator slider

Holding the glass, unscrew the two screws 2, Figure 4, securing the glass clip 1 to the slider, remove the glass from the door (Torx T20 screwdriver).

Window regulator fastening: 1 - front door molding fastening screw; 2 - safety buffer fastening screw; 3 - safety buffer; 4 - window regulator fastening nut; 5 - front door window regulator

Using a 10 mm spanner, unscrew the three nuts 4, Figure 5, and remove the window regulator 5 through the opening in the door panel, disconnecting the wiring harness connector from it.

Using a T20 Torx screwdriver, unscrew the two screws 2, and remove the safety buffer 3 through the opening in the door panel.

Fastening the outer handle: 1 - outer handle fastening nut; 2 - outer handle of the front door

Using a 10 mm spanner, unscrew the two nuts 1, figure 6, remove the outer handle 2, disconnecting the door lock rods from it.

Front door lock cylinder fastening: 1 - glass guide; 2 - outer cylinder fastening bracket; 3 - lock switch

Remove spring clip 2, figure 7, fastening switch 3 of the front door lock, remove the switch, disconnecting the lock rods from it.

Front door lock fastening: 1 - front door lock fastening screw; 2 - front door lock; 3 - front door glass guide fastening screw; 4 - screw securing the front door molding

Using a T30 Torx screwdriver, unscrew the three screws 1, Figure 8, securing the front door lock 2, remove the lock by disconnecting the wiring harness connector from it.

Using a T20 Torx screwdriver, unscrew the screw 3, remove the guide 1 (see Figure 7).

Door moldings and outside rearview mirror: 1 - outside rearview mirror; 2 - front door molding; 3 - rear door molding

Use a Torx T20 screwdriver to unscrew screw 4, fastening molding 2, Figure 9, overcoming the resistance of the holders and remove the molding.

Rear-view mirror fastening: 1 - rear-view mirror fastening bolt

Unscrew two bolts 1, Figure 10, fastening the outside rear-view mirror 1 (see Figure 9), remove the mirror

Front door fastening: 1 - door to hinge fastening nut: 2 - door opening limiter; 3 - door limiter fastening nut; 4 - protective cover of the wiring harness

Using a 10 mm head, unscrew the two nuts 3, Figure 11, securing the limiter 2 to the door

Remove the protective cover 4 of the wiring harness and the wiring harness from the door.

Using a 13 mm wrench, unscrew the four nuts 1 securing the door to the hinge, remove the front door (perform this operation with an assistant).

Installation

Installing the door assemblies and parts is carried out in the reverse order of removal, while:

- lubricate the rubbing parts of the window regulator, the sliding surfaces in the door lock, the door opening limiter, the rod joints and the hinges;
- before installing the upholstery, connect the ground wire terminal to the battery, check and, if necessary, adjust the operation of the door lock, check the operation of the window lifter, lift the drop-down window up;
- if necessary, restore or replace the sealing gasket on the end of the trim;
- ensure uniformity of the gap between the door and the mating body panels