Prepare the car for work, disconnect the negative terminal of the battery.
Removing the front seat
Press the lever 4, figure 1, up and move the seat 1 to the extreme rear position.
Using the Torx T40 head, unscrew the two bolts 3 securing the runners 2.
Press the lever and move the seat to the extreme front position.
Using the Torx T40 head, unscrew the two rear bolt 1, figure 2, runner fastenings, disconnect the rear wiring harness pads from the seat, remove the seat.
Removing the rear seat
Take the front edge of the cushion 1, figure 3, of the rear seat with your hands and pull it up until the loop 2 of the cushion frame comes out of the hole in the retainer 3 on the body.
Repeat this operation on the other side of the seat.
Grab the cushion 1, figure 4, of the rear seat, move it back towards the trunk, then lift the rear edge of the cushion to remove the loop 2 of the cushion frame from the grip 3 on the body.
Repeat this operation on the other side of the seat, remove the rear seat cushion from the car interior.
Using a 14 mm head, unscrew bolt 5, Figure 5, securing the right seat belt buckle and the lower attachment point of the middle seat belt.
Using a 14 mm head, unscrew bolt 3 securing the rear seat back bracket to the body floor.
Tilt the right seat back 4 and the left seat back 6 forward by pulling up the clamps 1 and 2.
Using a 14 mm head, unscrew the bolts 1, Figure 6, securing the brackets of the left 2 rear seat back, remove the back.
Unscrew the bolts 1 securing the brackets of the right 3 rear seat back, remove the back.
Install the seat in the reverse order of removal.
When installing the front seats, apply grease such as "Fiol-1" to the rubbing surfaces of the runners.
Removing the rear shelf trim
Remove the rear seat cushion as described above.
Using a 14 mm head, unscrew the bolts of the lower mount of the right and left seat belts.
Lower the rear seat backs.
Remove the arch trim right and left sidewalls.
Using a Torx 20 head, unscrew the self-tapping screw 2, Figure 7, on the right and left sides, fastening the side window trim 1.
Disconnect the side window trim from the body by pulling the trim with a force that overcomes the force of the plastic holders.
Remove plastic buttons 2, figure 8, fastenings of trim 1 of the luggage compartment shelf.
Using a flat-head screwdriver, remove gaskets 3 of the right 4 and left 5 seat belts from the holes in the shelf trim.
Remove the luggage compartment shelf trim assembled with the trim of the right and left side window, passing them through the holes in the shelf trim seat belts and disconnecting the wiring harness connector from the additional brake light installed on the shelf trim.
Using a T20 Torx head, unscrew three self-tapping screws 4 for each side, Figure 9, fastening trim 1 and 2 of the side window to trim 3 of the shelf, separate the parts.
Reinstall in the reverse order of removal.
Tightening torque of the seat belt mounting bolts from 38 to 50 Nm (from 3.8 to 5.0 kgf.m).
Removing the seat belts
Removing the front seat belt:
Remove the front and rear threshold trim.
Remove the cap from the head of the bolt fastening the lower point of the seat belt, use a 14 head to unscrew bolt.
Remove the upper and lower B-pillar trim.
Using a 14 mm head, unscrew bolt 1, Figure 10, of the upper mount 2 of the front seat belt on the central pillar.
Using a T20 Torx head, unscrew the two screws securing the guide 3 of the seat belt webbing, remove the guide.
Using a 14 mm head, unscrew bolt 5 securing the reel 4 of the seat belt.
Remove the seat belt reel by disconnecting the connector of the harness 6 wires from the reel.
Move the front seat to the extreme rear position.
Using a 14 mm socket, unscrew bolt 2, Figure 11, securing seat belt lock 1 to the seat bracket, disconnect the lock wire connector 3 from the rear wiring harness connector, and remove the lock.
Removing the right and left rear seat belts:
Remove the rear seat cushion as described above.
Using a 14 mm head, unscrew bolt 4, Figure 12, fastening the lower point of the middle 2 seat belt and the right seat belt buckle.
Unscrew bolt 5 fastening the middle 2 and left 3 seat belt buckles.
Unscrew bolt 6 fastening the lower point of fastening the seat belt, right and left.
Remove the right and left side arch trim.
Remove the trunk shelf trim.
Using a 14 mm socket, unscrew bolt 2, Figure 13, fastening reel 1 of the right or left seat belt on the rear shelf panel, remove the reel.
Removing the rear its middle seat belt:
Remove the headrests of the right rear seat back, the headrest guides, unscrew the handle of the seat back locking mechanism, remove the handle trim of the locking mechanism and the seat belt tape from the holes in the seat back upholstery.
Remove the seat back upholstery and the seat back filler, threading the belt tape through the holes in the upholstery and filler.
Using a 17 mm head, unscrew nut 1, figure 14, securing reel 3 of the middle seat belt to frame 2 of the backrest, remove the seat belt reel by threading the belt tape through the loop on the backrest frame.
Install the seat belts in the reverse order of removal.
After opening the locks, the front and rear seat belts must return from the working position to the original position freely, without jamming.
Tightening torque of seat belt fastening bolts 38 - 50 Nm (from 3.8 to 5.0 kgf.m).
