Front door repair involves replacing door elements
Removing the outside mirror
Use a slotted screwdriver to pry off the exterior mirror trim
Remove the lining
Using pliers, remove the locking bracket of the handle rod ball joint housing
Use a Phillips screwdriver to unscrew the three mirror mounting screws
Remove the mirror along with the cables and the ball joint
Installing the outside mirror in reverse order
Removing and installing front door trim
Use your hand to unscrew the lock button.
Having turned the inner handle so that the screw securing it to the lever is accessible, use a Phillips screwdriver to unscrew the screw and remove the handle.
Use a screwdriver to pry off the switch block, squeezing the fastening latches
We take it out of the hole in the armrest and, unfolding it as shown in the photo, lower the block into the resulting hole so that it does not interfere with the removal of the door trim.
Use a Phillips screwdriver to unscrew the two screws for the lower fastening of the upholstery.
Use a screwdriver with a thin blade to pry the plug in the armrest and remove it from the hole
Use a Phillips screwdriver to unscrew the screw securing the upholstery
Unscrew the screw fastening the upholstery located in the armrest niche
Use your hands to move the lower edge of the upholstery away from the inner door panel, overcoming the resistance of the pistons.
We remove the upper edge of the upholstery from the groove of the internal glass seal and, solder Today we remove the upholstery from the front door.
If necessary, use a Phillips screwdriver to unscrew the four screws securing the energy-absorbing element of the door and remove it.
Install the upholstery in reverse order
Removing the front door glass
Removing the glass trim
Installing the glass in the upper position
Using a 8mm socket, unscrew the four bolts securing the glass to the two sliders and remove the glass
If necessary, peel off the protective film from the glass holder. Install the front door glass in reverse order.
Removing the front door power window
Remove the front door glass.
Disconnect the wire terminal from the negative terminal of the battery.
Before disconnecting the power window mechanism wire block from the switch block wire block, unroll the wrapping material on the connection of the blocks and disconnect the blocks
Using a 10mm socket, unscrew the 11 nuts securing the power window mechanism.
We remove the power window mechanism from the door through the lower hole in the interior panel.
Install the power window mechanism in reverse order.
In order to prevent knocking on the doors, we cover the connection of the pads with soft material (foam rubber).
Removal and installation of the external handle and lock of the front door
Remove the front door trim.
Use a Phillips screwdriver to unscrew the screw securing the base of the inner handle and remove it from the mounting pin.
Bend the edge of the protective material behind the inner door panel.
Using a screwdriver, we disconnect the rod from the cylinder mechanism of the outer handle lock.
We disconnect the rod of the outer handle in the same way.
Use a 8mm socket to unscrew the bolt securing the outer handle.
Use an 8-mm socket to unscrew the handle fastening nut
Remove the outer handle.
Use a Phillips screwdriver to unscrew the three screws securing the door lock.
Move the red block lock up and disconnect the block from the locking drive
Use a screwdriver to press out the rod lock, turning it around its axis.
Having disconnected the rod of the inner handle from the lock, remove the rod.
We remove the front door lock together with the locking drive and rods through the technological opening in the inner door panel
Install in reverse order
Removing and installing the door limiter
Remove the door trim.
To avoid damaging the door, do not swing it open after removing the stopper.
Use a 13 mm socket wrench to unscrew the bolt securing the limiter to the body pillar.
Use an 8 mm socket wrench to unscrew the two bolts securing the limiter to the door
Remove the limiter from the internal cavity of the door. Install the limiter in the reverse order, and then cover it with any grease
Removing and installing the front door
The door can be removed as an assembly (together with the equipment installed on it).
It is more convenient to disassemble and assemble the door when it is installed on the car.
At the same time, there is less chance of damaging the paintwork. An assistant will be required to complete the work.
- 1. Remove the window regulator.
- 2. We remove the glass from the door.
- 3. Remove the outer door handle.
- 4. Remove the door lock.
Unscrew the nut securing the wiring harness and disconnect the wiring harness block from the door harness block.
Release the three latches and remove the wiring harness block from the door hole.
Disconnect the wiring harness from the inner door panel and remove the harness through the hole in the door.
Remove the door stop.
While an assistant is holding the door, use a 13 mm spanner to turn out the axis of the lower hinge
Use the same key to unscrew the upper hinge axis and remove the door.
Having covered the working surfaces of the hinges and axles with grease, install and assemble the door in the reverse order.
To ensure reliable contact in the connecting block of the door wiring harness, we treat its terminals with a special agent for cleaning and protecting electrical contacts.
